Questions asked in SSC JE 2016 Exam (Design of steel structures)

Please share with your friends and subscribe this blog by e-mail to get notification.

Up coming soon- SSC JE previous years paper from 2001 to 2019

2016(All sets)

1. As per ISI, rolled steel beam sections are classified into ____________ .

a) two series

b) three series

c) four series

d) five series

2. The channels get twisted symmetrically with regard to its axis________.

a) Parallel to flanges

b) Parallel to web

c) Perpendicular to flanges

d) Perpendicular to web

Questions asked in SSC JE 2015 Exam (Design of steel structures)

Please share with your friends and subscribe this blog by e-mail to get notification.

Up coming soon- SSC JE previous years paper from 2001 to 2019

2015

1. When a load is exerted or transferred from one surface to another in contact, the stress is known as?

a) Bearing stress

b) binding stress

c) Shear stress

d) direct stress

2. The steel beam of light section placed in plain cement concrete are called.

a) Joists

b) concrete joists

c) filler joists

d) simple joists

Questions asked in SSC JE 2013 Exam (Design of steel structures)

Please share with your friends and subscribe this blog by e-mail to get notification.

Up coming soon- SSC JE previous years paper from 2001 to 2019

2013

1. A structure which offers negligible of zero resistance on bending at any point is known as:

a) Beam

b) Girder

c) Lintel

d) Cable

2. The distance between two rivets measured perpendicular to the direction of applied force is known as:

a) Pitch

b) Gauge

c) Staggered pitch

d) Edge distance

Questions asked in SSC JE 2012 Exam (Design of steel structures)

Please share with your friends and subscribe this blog by e-mail to get notification.

Up coming soon- SSC JE previous years paper from 2001 to 2019

2012

1. The slenderness ratio (𝑙/𝑟) of a lacing bar should be less than

a) 250

b) 350

c) 145

d) 180

2. The member of roof truss which supports the purlins is called as

a) Sag rod

b) Main strut

c) Principal rafter

d) Principal tie

Questions asked in SSC JE 2011 Exam (Design of steel structures)

Please share with your friends and subscribe this blog by e-mail to get notification.

Up coming soon- SSC JE previous years paper from 2001 to 2019

2011

1. If a 2 cm diameter rivet connects two plates as shown below and safe shear stress for rivet is 1000 kg/cm2 the value of maximum permissible pull will be

a) 1100 kg

b) 1140 kg

c) 2140 kg

d) 3140 kg

2. According to IS : 800-1984, the permissible stress in axial tension in steel is [ fy = minimum yield stress of steel]

a) 0.56 fy

b) 0.66 fy

c) 0.70 fy

d) 0.6 fy

Questions asked in SSC JE 2009 Exam (Design of steel structures)

Please share with your friends and subscribe this blog by e-mail to get notification.

Up coming soon- SSC JE previous years paper from 2001 to 2019

2009

1. If p and d are pitch and gross diameter of rivets, the efficiency 𝜂’ of the riveted joint, is given by

a) 𝜂 = p/ (p - d)

b) η = (p - d)/ p

c) 𝜂 = p / (p + d)

d) 𝜂 = (p + d)/ p

2. The permissible bending stress in steel is

a) 1500 kg/cm2

b) 1890 kg/cm2

c) 1900 kg/cm2

d) 1300 kg/cm2

Questions asked in SSC JE 2008 Exam (Design of steel structures)

Please share with your friends and subscribe this blog by e-mail to get notification.

Up coming soon- SSC JE previous years paper from 2001 to 2019

2008

1. Net sectional area of a tension member is equal to its gross sectional area

a) Plus the area or rivet holes

b) Divided by the area of the rivet holes

c) Multiplied by the area of the rivet holes

d) Minus the area of the rivet holes

2. A tension member, if subjected to possible reversal of stress due to wind, the slenderness ration of member should not exceed

a) 126

b) 200

c) 250

d) 350